Page MenuHomeAleph Objects Inc

draubach (Dylan Raubach)
User

Projects

User Details

User Since
Mar 20 2018, 10:36 AM (78 w, 11 m)

Recent Activity

Yesterday

draubach added a comment to T10064: Lines across some LCDs when tightened into CB assembly.

@logan I have talked to Aeron and let him know to set one aside when/if they find another issue like this

Mon, Sep 16, 11:10 AM · Redgum

Mon, Sep 9

draubach closed T9890: EL-HR0181 Y-Z End Harness, Assembled Rev c / CCX review request as Resolved.
Mon, Sep 9, 1:11 PM
draubach added a comment to T9890: EL-HR0181 Y-Z End Harness, Assembled Rev c / CCX review request.

Didn't realize that we had received more of them. Got the harnesses and gave them a check over. Everything looks good and this should be good to go to Resolve this ticket

Mon, Sep 9, 1:11 PM

Thu, Aug 29

draubach added a comment to T9890: EL-HR0181 Y-Z End Harness, Assembled Rev c / CCX review request.

@david.hall the only material we are using for this rework is the heat shrink. 30 mm of HD-TB0075 per harness.

Thu, Aug 29, 3:07 PM
draubach added a comment to T9890: EL-HR0181 Y-Z End Harness, Assembled Rev c / CCX review request.

Also in regards to @david.hall's comment, we were planning on reworking 250-500 of these harnesses. As of this morning we have 130 reworked. I am very happy to continue with the reworks as this harnesses is the most time consuming harness we have had since I started working here and the reworks take all of maybe 5 minutes per harness.

Thu, Aug 29, 2:30 PM
draubach added a comment to T9890: EL-HR0181 Y-Z End Harness, Assembled Rev c / CCX review request.

The connector is within the heat shrink on both ends of the harness and can't be inside the top heat shrink as that part of the harness sits within the interconnect housing and the black wires would not be able to get plugged in when the control is added to the rest of the printer. Personally, I don't think a zip tie or anything is really necessary to hold it in place. It's within the heat shrink on the other end, shares a connector with the ground on that end, the sleeve holds a pretty good grip on wires, and when it is plugged in on the printer I would imagine that would also help keep it in place. Then again, I just build the cables, so I may just be spitting out nonsense. But the end at the top where all 3 grey wires share a single connector, the black absolutely cannot be in that heat shrink.

Thu, Aug 29, 2:27 PM
draubach added a comment to T9371: Bed Heater External wire length for zip tie at calibration.

Can do

Thu, Aug 29, 12:35 PM · Redgum

Wed, Aug 28

draubach added a comment to T9842: Wire harnesses pinned wrong.

Real quick input here as well. @logan is aware and we have discussed fixing this issue, but we are only able to do the wire test on 2 harnesses for redgum currently. The internal and external YZ harnesses are the only ones that can be caught in testing before being put in a control box. That being said, these issues should still be caught at the CB Test, so this is no excuse. Just clarification.

Wed, Aug 28, 10:07 AM · Redgum

Aug 7 2019

draubach added a comment to T9371: Bed Heater External wire length for zip tie at calibration.

heat shrink is not placed to current documentation rev

Aug 7 2019, 5:13 AM · Redgum

Aug 6 2019

draubach added a comment to T9371: Bed Heater External wire length for zip tie at calibration.

And we have some of these from CCX. Will CCX rework the ones they sent us, or will we need to rework them like with what happened with the EL-HR0160s a few weeks back?

Aug 6 2019, 11:26 AM · Redgum
draubach added a comment to T9371: Bed Heater External wire length for zip tie at calibration.

@logan So if it's 420-425mm, it's usable?

Aug 6 2019, 11:23 AM · Redgum
draubach added a comment to T9371: Bed Heater External wire length for zip tie at calibration.

@kent comparing the documentation you posted with the one we have in Electro-Mech, there is a difference in spacing for the side opposite of the 10 mm spacing. Ours is calling for 15 mm from end of heat shrink and the one you shared is only calling for 5 mm of heat shrink coming off of the side opposite the 10 mm spacing. So we have not been measuring these out completely due to old documentation. We can definitely make this change and add this to all current wires we have made

Aug 6 2019, 5:38 AM · Redgum

Jul 31 2019

draubach added a comment to T8533: AS-CB0075 rev in filename doesn't match rev on drawing.

@kent I don't think that would have had any sort of effect on how we built it if the drawing itself wasn't incorrect.

Jul 31 2019, 3:22 PM · Mini-Hibiscus

Jul 16 2019

draubach changed the visibility for T8798: EL-HR0144 Inquiry.
Jul 16 2019, 11:31 AM · Quiver

Jul 3 2019

draubach added a comment to T7795: USB drives shorting out..

Yes all ribbon wire LCD harnesses should be getting tested as Logan said. I will look into whether or not ALL have been getting tested and make sure they do from here on out.

Jul 3 2019, 1:17 PM · Quiver

Jun 6 2019

draubach changed the edit policy for T7659: Interconnect Housing - endstop wire retention.
Jun 6 2019, 10:00 AM · Quiver

Jun 3 2019

draubach triaged T7621: Workhorse OHAI Issue as Unbreak Now! priority.
Jun 3 2019, 2:15 PM · Redgum

May 29 2019

draubach created T7525: Cable Documentation Issues.
May 29 2019, 5:02 PM · Redgum
draubach changed the edit policy for T7523: Cable Harness Documentation Change Request.
May 29 2019, 4:55 PM · Quiver

Apr 4 2019

draubach created T6491: ..
Apr 4 2019, 8:26 AM · Unknown Object (Project)

Jan 23 2019

draubach changed the edit policy for T5473: El-Hr0140/141 Heat Shrink Size.
Jan 23 2019, 11:32 AM · Unknown Object (Project)

Jan 22 2019

draubach changed the edit policy for T5448: EL-HR0153 Documentation Discrepancy .
Jan 22 2019, 10:22 AM · Quiver

Nov 28 2018

draubach changed the edit policy for T4732: EL-HR0155 Documentation Quantity Error.
Nov 28 2018, 12:27 PM · Quiver

Sep 5 2018

draubach triaged T3523: v2 aero adapter mini wiring harness drawing as Normal priority.
Sep 5 2018, 9:12 AM · Retail Parts